Search results

As per software I sent the logs

On your new version, v2024.4.9853, the dism remove left over componet removal doesn't show when you start the process to start NTLITE. The size of the iso went from 5,553,532,928 bytes for version 2024.3.9819 to 7,009,077,248 bytes for version v2024.3.9853. The must be an error some where...

Its been awhile since we had a new version of NTLITE; 2023_12_9552_x64. Looking forward to the the next version.

The same error occured, 0x80070643 after doing a host refresh. Once the February update was reinstalled, then kb5034441 was reapplied, the error no longer exists. After examining the software distribution folder, I found the following file; WinREUpdateInstaller_2401B_amd64.exe. However this...

I received this error on Jan 9 when I did a host refresh; The error indicates a net framework error. However, this update is not part of the download when you check for online updates; My version of windows is win1022H2

Not sure where this exe is tied to. But it shows up in my autoruns. Initial searches say that it is tied to diagnostics and feedback.. This is the first time this exe showed up in my autoruns

The default frequency is set to daily by default. It will only invoke retrim if required. I would like to set the frequency to monthly.

By default windows the frequency is set "daily" and only optimize the drive if needed. Windows has the option of changing the frequency do weekly or monthly depending on the user's preferency. Is their a setting in Ntlite that will allow me to change the frequency. Basically, googling this...

I tried the new tool 8775 today and partially through removing components it crashed to the desktop. I included the log files for both 8775 and 8714. Note no issues with 8714. When the tool crashed it was removing 3d viewer. Hope info helps

This is something new. Saw this error when doing a fresh install today. Included my preset. All I did was rebooted. And I logged in. Periodically I see this error.

Is there a way to disable the value banner that shows in the windows settings. Unfortunately it show its ugly head again. Before I use Mach2 which you can download from the internet and the following command lines I have been using. mach2.exe disable 18299130 mach2.exe disable 31950543

Not sure what this options does. It appears that it does not influence DISM /online /image-cleanup /startcomponentcleanup in cleaning the WINSXS folder. Nuhi could you please explain this option. Thank-you

Looks like the commands were not executed?

The following options are checked; System Reset for Windows Windows update (+Feature Setup) Under settings DISM resetbase functionality disabled; When I decide to clean the winsxs folder to remove obsolete entries: First I run the following command {Cmd mode; Admin} cleanmgr sageset:50 I...

Side effect when I did a fresh install of windows 10 with windows store correctly implemented I had to reactivate NTlite. Not sure it was the result of using the Nvidia DCH driver. But the number of re-activations left is now TWO. I do plan to do another fresh install when 21H2 is released...

The check-marks used to indicate what you pick or do not pick in component removal are at times very difficult to see. A light shade a grey makes this difficult to see. May I suggest different color check marks. Red for Locked Components, orange for compatibility features for example.

With nvidia going forward with their new drivers the control panel now must be installed via windows store. The reason I went to the newer driver is a improved security with 496.49. I have updated my configuration, preset attached. Windows store is working, but the nvidia control panel will...

The new version processes the image file correctly, but hangs at the very end during the cleaning phase,.

The last couple of updates I have had to reinstall the non-DCH nvidia driver after host refresh. Apparently the non-dch driver gets over written. Which means I have to go into safe mode and use the DDU utility. Yes, I have used GPO settings to not allow driver updates from windows update...

There are times when an ISO needs to be mounted for proper installation of an application. Is there a way to mount an ISO during windows installation to install an application?