Event Viewer Channels bugged?

MT_

Active Member
Hi! I disable a ton of these, but everytime i notice only a few remain after reloading the xml.

Now i tried disabling a lot of them again, and saved the xml manually and investigate, and this shows up (Just a fraction example):

<Tweak name="Packaged app-Deployment\Enabled">0</Tweak>
<Tweak name="Packaged app-Execution\Enabled">0</Tweak>
<Tweak name="Admin\Enabled">0</Tweak>
<Tweak name="Admin\Enabled">0</Tweak>
<Tweak name="Microsoft-Windows-Backup\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="WHC\Enabled">0</Tweak>
<Tweak name="BackupLog\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Microsoft-Windows-Known Folders API Service\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Debug\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="SMSApi\Enabled">0</Tweak>
<Tweak name="Admin\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Debug\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Certification\Enabled">0</Tweak>
<Tweak name="CompatAfterUpgrade\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>
<Tweak name="Admin\Enabled">0</Tweak>
<Tweak name="Operational\Enabled">0</Tweak>


A lot of dummies or something. Or is this because these elements are tagged for component removal that these don't work properly to begin with?
But they seem bugged.

When I apply the image and process it they do seem to appear in what NTLite is doing while processing the image, so I guess its applying it on building but the next time you use the same profile they are gone as they arent properly saved to xml.
 
Last edited:
Thanks for reporting this, will fix for tomorrow's maintenance release.
 
Thank you!

Can you tell me whether they do apply to a build? Otherwise ill have to rebuild it.

Edit: I think it did apply actually.
 
Last edited:
The state of the channels can be seen by opening that image/installation in NTLite, it will show real states.
Just saving to preset didn't work, but since this applies also to the in-memory ones between reloads inside a single session (e.g. after updating, reloading then continuing with the process), it's difficult to comment in which situation it applied.
So best is to just load the target and see current states in the UI, also it's not difficult to disable then directly.
 
Back
Top